They will take the car for a drive. Just after you pick it up drive and make sure that the wheel is straight.
Also tell them that the car has been following the lines in the road a lot. They can actually align the car to compensate for the natural camber in the road.
Don't be scared to take it back to them if you are not happy, and also make sure all your tyre pressures are correct before the alignment.
***** ALERT - Nominations for your new ClubCJ Committee can be made here *****
Is it worth getting a strut bar?
Moderators: Moderators, Senior Moderators
This morning before I drove to work I softened the front damping and hardened the back...
It seems to have helped a bit. Pretty sure the problem is that the front damping was set too hard compared to the back but I'll make it a point to change them every morning to see. Might try the extremes to make the differences more obvious to me.
Another thing I've been finding is an odd weight shift diagonally across the car on gentle bends rather than just to the side. Might not sound like a big deal but its enough to almost give me a vertigo feeling sometimes. Softening the front seems to have helped that as well.
It seems to have helped a bit. Pretty sure the problem is that the front damping was set too hard compared to the back but I'll make it a point to change them every morning to see. Might try the extremes to make the differences more obvious to me.
Another thing I've been finding is an odd weight shift diagonally across the car on gentle bends rather than just to the side. Might not sound like a big deal but its enough to almost give me a vertigo feeling sometimes. Softening the front seems to have helped that as well.
The UR bar is as simple as possible so its cheaper.
I had an Alutec bar and they're extremely light despite being a bit chunky looking. They're also good quality. Perhaps they're better value for money than Whiteline.
However when I bought my Alutec bar from RPW they didn't give me all the bits, so keep that in mind
If you're looking at RPW's website remember those prices don't include GST, and you'd have to pay for postage too (isn't it illegal to advertise prices without GST...? Lol)
The link to the Whiteline bar I posted further up is on a site that does free postage Australia-wide, so you pay what it says.
I had an Alutec bar and they're extremely light despite being a bit chunky looking. They're also good quality. Perhaps they're better value for money than Whiteline.
However when I bought my Alutec bar from RPW they didn't give me all the bits, so keep that in mind
If you're looking at RPW's website remember those prices don't include GST, and you'd have to pay for postage too (isn't it illegal to advertise prices without GST...? Lol)
The link to the Whiteline bar I posted further up is on a site that does free postage Australia-wide, so you pay what it says.
- RennieJames
- Lancer VR/GT
- Posts: 271
- Joined: Sat Mar 17, 2012 11:07 pm
- Location: Townsville
Well the one I bought as posted above is great but as I thought you can feel a difference but not to massive just enough for you to feel it. The strut bar i got was pretty expensive but that was the best one on ebay that i could find the delivered within a week ( I think because they are located in Brisbane and Sydney not 100% sure though ) but I wanted to put it on before the drive to Townsville on Sunday
Everything was in there when i opened it:
- Strut bar
- 6 washers for under the strut bar. ( if there is something else that is ment to be there let me know )
I can not recommend it yet as I've only had it for a couple of days but so far so good
- Rennie
Everything was in there when i opened it:
- Strut bar
- 6 washers for under the strut bar. ( if there is something else that is ment to be there let me know )
I can not recommend it yet as I've only had it for a couple of days but so far so good
- Rennie
My Build thread : http://clubcj.net/viewtopic.php?p=335538#335538
-
- Lancer Newbie
- Posts: 43
- Joined: Wed Aug 29, 2012 11:01 pm
- Location: Darwin, NT
I've been reading up on strut bars and will probably get one for the front tower and an adjustable one for the rear, thanks for all the input and opinions all. I'm probably picking up my Activ Sportback next week or so, and I reckon I'll drive that around for awhile to help me make up my mind. I'm not superstitious, but I really don't want to be ordering parts for a car that I don't even have with me yet, ha ha!
- cj_sx_2011
- Lancer Ralliart
- Posts: 634
- Joined: Fri Sep 16, 2011 12:19 am
- Location: south australia
whoever still is unsure bout the strut brace, dont think so much about it its not an expensive mod, i think i got my ultra racing strut brace for 150 delivered,
i had the strut brace on before having coilovers, and i noticed a big difference in the the front and stiffing it up over bumps and around round-a-bouts and made a decent amount of difference in the hills to,
so highly recommended from me.
i had the strut brace on before having coilovers, and i noticed a big difference in the the front and stiffing it up over bumps and around round-a-bouts and made a decent amount of difference in the hills to,
so highly recommended from me.
Re: Is it worth getting a strut bar?
Have to give positive feedback on Ultra racing
Who is online
Users browsing this forum: No registered users and 57 guests