***** ALERT - Nominations for your new ClubCJ Committee can be made here *****

How to stop subs from moving?

Lancer Interior Modifications.

Moderators: Moderators, Senior Moderators

User avatar
tadz0rz
Genius
Genius
Posts: 6955
Joined: Sun Mar 08, 2009 8:54 pm
Location: Melbourne, VIC, Australia
Contact:

Postby tadz0rz » Wed Apr 15, 2009 9:49 pm

Epic fail for crappy drivers
Got a question? Read the ClubCJ Ultimate Guide First!!
Image
Just...Dont worry about it ;)Dont Click Me

Dummer

Postby Dummer » Wed Apr 15, 2009 11:33 pm

a packet of 4 75mm square brackets from bunnings and a pack of 25mm 8guage steel self drilling steel screws. about $12 from bunnings. line the brackets and sub up, mark around the outline of the sub on the sub box with masking tape. take sub box out, line brackets back up using the masking tape and use a 2 or 3mm drill bit to drill pilot holes into the sub box. the back off the bracket pack i had said use a 3mm drill bit, but i think that was too big and 2mm was more appropriate. put a phillips head bit in the drill, turn the clutch torque down lowish and then drive the screws into the box to hold the brackets down...back into the car, line it up (u might need tobend the brackets back from 90 degrees a lil bit) get a self drilling screw put it through the whole on the bracket, apply pressure and the screw will drill and taps its own hole :P

I'll get pics for you tomorrow of how i secured my Kicker L7

User avatar
tadz0rz
Genius
Genius
Posts: 6955
Joined: Sun Mar 08, 2009 8:54 pm
Location: Melbourne, VIC, Australia
Contact:

Postby tadz0rz » Wed Apr 15, 2009 11:38 pm

Ryan you are the man. Thank you.

I also asked ozie about this, Im a nice moderator and since you made the best reply and therfore the most help

I award you 100 extra points. Congradulations
Got a question? Read the ClubCJ Ultimate Guide First!!

Image

Just...Dont worry about it ;)Dont Click Me

User avatar
ANDROS
Lancer Legend
Lancer Legend
Posts: 1031
Joined: Wed Mar 18, 2009 8:41 am
Location: Melbourne, VIC, Australia

Postby ANDROS » Thu Apr 16, 2009 1:38 pm

on my previous car i used velcro strips underneath the sub. didnt move at all
___________________________________________________

User avatar
Hoggy
INACTIVE Member Account
Posts: 454
Joined: Tue Nov 11, 2008 7:18 am
Location: Central Coast, NSW

Postby Hoggy » Thu Apr 16, 2009 2:56 pm

If you have the time and can be bothered I would put a false front on the box that fits the boot exactly running it into every edge - will give it a much more custom made look as well as securing the box in place.

Shouldn't cost you much as doesn't need to be thick MDF and then just buy some carpet that matches the existing carpet.
Image

dumb&

Postby dumb& » Thu Apr 16, 2009 3:00 pm

Hoggy's idea is a good one, but if you don't want to go to that much effort a few decent strips of thick velcro is the easiest method without having to drill into anything. Unless you drive with reckless abandon you should be fine with some velcro :)

User avatar
ANDROS
Lancer Legend
Lancer Legend
Posts: 1031
Joined: Wed Mar 18, 2009 8:41 am
Location: Melbourne, VIC, Australia

Postby ANDROS » Thu Apr 16, 2009 3:02 pm

you can also use velcro under the boot carpet and attatch it to the spare wheel cover. this will stop the carpet from moving.... and then u can drive wreckless as much as u want :)
___________________________________________________

User avatar
Speedie
Lancer MASTER
Lancer MASTER
Posts: 1751
Joined: Thu Mar 05, 2009 11:42 pm
Location: Brisbane, QLD, Australia

Postby Speedie » Thu Apr 16, 2009 5:35 pm

Or get them installed properly
Image

[Evo X Brembos] [Evo X Intercooler] [Evo X UICP]


Return to “Interior”

Who is online

Users browsing this forum: No registered users and 30 guests